設為主頁 | 加入收藏 | 產品展示 | 聯系正睿 |

歡迎訪問濟南正睿廣告有限公司官網!

楊經理

13969120902

您先的位置:首頁 > 新聞資訊 > 公司新聞

公司新聞

正確安裝濟南百葉窗的小常識

文章發布: 發表時間:2017-07-18 10:13:16

1、窗框與墻體的銜接

窗框與墻體的固定辦法,多見的有銜接件法、直接固定法和假框法三種。
濟南百葉窗裝置效果圖銜接件法:是用一種專門制造的鐵件將窗框與墻體相銜接,其長處是對比經濟,且基本上能夠確保窗的穩定性。銜接件法的做法是先將塑料窗放入窗洞口內,找平對中后用木楔暫時固定。然后,將固定在窗框異型材靠墻一面的錨固鐵件用螺釘或脹大螺絲固定在墻上。
Ji'nan shutter device connector renderings: using a specially made iron window frame and the wall will be connected, its advantages are the economic comparison, and basically can ensure the stability of the window. The connecting piece method is first put into the plastic window in the window opening, leveling of temporary fixation with wedge. Then, will be fixed on the window frame profiles against the wall side of the iron anchor with screws or expansion screws on the wall.
直接固定法:在砌筑墻體時先將木磚預埋入窗洞口內,當塑鋼窗安入洞口并定位后,用木螺釘直接穿過窗框與預埋木磚銜接,從而將窗框直接固定于墻體上。
Direct fixation: in the first brick masonry wall embedded into the window, when the window into the mouth and an orientation, with wood screws directly through the window frame and the embedded block connection, which will direct the window frame fixed on the wall.
假框法:先在窗洞口內裝置一個與塑鋼窗框配套的鍍鋅鐵皮金屬框,或許當木窗換成塑鋼窗時,將本來的木窗框保存,待抹灰裝飾完成后,再將窗框直接固定在上述框材上,最后再用蓋口條對接縫及邊際有些進行裝飾。
False box method: first window opening device in a plastic steel window frame and supporting the galvanized sheet metal frame, perhaps when the wooden windows replaced steel windows, the wood window will have to be preserved, plastering decorative finishes, the window frame is directly fixed on the frame, and then cover the mouth of butt joint and marginal some decoration.
2、斷定銜接點方位
2, determine the direction of the convergence point
斷定銜接點的方位時,首先應考慮能使窗扇通過合頁效果于窗框的力,盡可能直接傳遞給墻體;斷定銜接點的數量時,有必要思考避免濟南百葉窗在溫度應力、風壓及其它靜荷載效果可能發生的變形;銜接點的方位和數量,還有必要確保在塑鋼窗與墻體之間細小的位移,不致影響窗的運用功能及銜接本身。
Determine the connection point range, should first consider the window sash window frame through hinges on the effect of force, directly to the wall as far as possible; that number of connection point, it is necessary to think how to avoid deformation of Ji'nan blinds stress, pressure and other static load effect may occur in the temperature range and the number of connection points; also, the need to ensure that small displacement between the window and the wall, the window does not affect the function and use of cohesion itself.
3、框與墻間縫隙處理
3, the gap between the frame and wall treatment
因為塑料的脹大系數較大,故要求窗框與墻體間應留出必定寬度的縫隙,以習慣塑料彈性變形的安全余量。框與墻間的縫隙,運用泡沫塑料條或油氈卷條填塞,填塞不宜過緊,避免框架變形。窗框附近的表里接縫運用密封資料嵌填緊密。也能夠選用硅橡膠嵌縫條,不宜選用嵌填水泥砂漿的做法。
Because the plastic swell coefficient is larger, so the requirements between the window frame and the wall should be set aside by the width of the gap will, the elastic deformation of the plastic used safety margin. The gap between the wall and the frame, the use of foam or rolling packing, packing should not be too tight to avoid deformation of the frame. The table near the window frame using the joint sealing material filling closely. Can also use silicon rubber sealing strip, should not use cement mortar filling approach.
填縫關鍵兩點:榜首,嵌填封縫資料應能接受墻體與框間的相對運動而保持密封功能;第二,嵌填封縫資料不應對塑料窗框有腐蝕、軟化效果,瀝青類資料可能使塑料軟化,故不宜運用。
Key points: first, filling filling sealing material should be able to accept the relative motion between the wall and the frame while maintaining the sealing function; second, filling sealing materials should not plastic window frame corrosion, softening effect of asphalt materials may make the plastic softening, it should not be used.
4、五金配件裝置
4, hardware accessories
塑鋼窗裝置五金配件時,有必要先在桿件上鉆孔,然后用自攻螺絲擰入,禁止在桿件上直接捶擊釘入。
Plastic windows device hardware accessories, it is necessary to drill holes in the rod, and then use self tapping screws into, is prohibited in the bar directly hammering nails into the.
5、清洗
5, cleaning
窗框扇裝置后應暫時取下扇,編號獨自保管。窗洞口粉刷時,應將窗表面貼紙維護。粉刷時如框扇沾上水泥漿,應立即用軟料抹布擦拭潔凈,切勿運用金屬工具擦刮。粉刷結束,應及時清除玻璃槽口內的渣灰。
Window frame device should temporarily remove fan numbers alone custody. Window paint, the surface of the window sticker should be maintained. When painting, such as the frame of the fan with cement paste, should immediately wipe with a soft cloth wipe clean, do not use metal tools scratch. Paint the end, should be promptly removed in the notches of the slag glass.

福利AV导航