設為主頁 | 加入收藏 | 產品展示 | 聯系正睿 |

歡迎訪問濟南正睿廣告有限公司官網!

楊經理

13969120902

您先的位置:首頁 > 新聞資訊 > 行業新聞

行業新聞

濟南彩鋼板房彩鋼板的施工要點

文章發布: 發表時間:2017-07-18 11:02:29

彩鋼板裝置的固定辦法有穿透式和暗扣蔭蔽式兩種。穿透式固定是屋面和墻面彩鋼板裝置的最常用辦法,即用自攻螺釘或鉚釘將彩板固定在支持件(如檁條)上,穿透式固定波峰固定、波谷固定或他們的組合。暗扣蔭蔽式固定是將與暗扣式彩板配套的特制暗扣先固定在支持件(如檁條)上,彩板的母肋與暗扣的基地肋齒合的固定辦法,一般用于屋面板的裝置。

Fixed way color plate device through type and dark shade type two. Transmission is the most commonly used way of fixed roof and wall color steel plate device, which is self tapping screw or rivet colorplate fixed on the support member (e.g., purlin) penetrating fixed crest and trough fixed fixed or their combination. Dark shade type fixation is matched with the dark color of button plate special dark buckle first fixed on the support member (e.g., fixed base purlin) to rib rib and mother tooth color plate of the button, the general device for roof panel.
彩鋼的側向和端部搭接。裝置每一塊鋼板時,應將其邊搭接精確地放在前一塊鋼板上,并與前一塊鋼板夾緊,直到鋼板的兩頭都固定停止。一種簡略而有效的辦法是用一對夾口鉗別離夾住所搭接的鋼板。鋼板沿縱向就位時,其端部尤其是上端部需用鉗子夾住搭邊有些,這么可確保鋼板一端的就位,并使一端的搭接也處于正確的方位,從而固定住鋼板,在固定的過程中,夾鉗一直應在縱向夾住鋼板。在裝置下一塊鋼板之前,每塊鋼板有必要徹底被固定住。固定有必要始于鋼板的基地,然后向兩頭伸展,終究固定鋼板的搭接邊。對于端部搭接,由于屋面和墻面外形板是用接連加工的辦法制成的,因而可按運送條件所約束的長度供給鋼板,一般不需求搭接,鋼板長度就足以滿足屋面鋪設的需求。
Side and end overlap of color steel. Each piece of steel plate, the edge should be accurately placed on the front of a piece of steel plate, and the front plate clamping, until both ends of the steel plate are fixed. A simple and effective method is to use a pair of pliers to separate the steel plate. Steel plate along the longitudinal position, the upper end of the end especially need pliers clamp on some edge, so that the plate is in place, and the end of the lap is in the right direction, so as to fix the plate, in the process of fixed clamp has in vertical clamp plate. Prior to the installation of a piece of steel plate, each plate is necessary to be completely fixed. It is necessary to start at the base of the steel plate, and then extend to both ends. For the end of the lap, the roof and wall plate shape is made of a series of processing methods, which can be delivered according to the length of steel supply conditions constraints, generally do not need the lap, the length of the plate is enough to meet the needs of the laying of the house.
出于對現場處理和運送思考,必要時可用兩塊較短的鋼板經過端部搭接來掩蓋全部長度,每一列鋼板的搭接次序順次從底部到頂部,然后再放下一列。對運用穿透式固定法的屋面和墻面鋼板端搭接需定位在支持上。對斜度在1/12(50)~1/4(150)之間的屋面,鋼板端部重迭長度最少為200mm;斜度超越1/4(150)時,重迭長度最少為150mm,而且鋼板端部重疊有些的中點應在支持件的基地。墻面板最小重迭長度為100mm。
In view of the handling and transport of the site, two short plates may be used to cover the entire length of the plate when necessary, and the order of the overlap of each plate shall be followed from the bottom to the top, and then a column shall be laid down. The roof and wall steel plate joint with the method of penetrating fixation should be positioned on the support. On the slope in 1/12 (50) ~1/4 (150) between the roof plate, the end overlapping length is at least 200mm; slope beyond 1/4 (150), the overlap length of at least 150mm, and the steel plate end overlap some of the support base in the middle. The minimum overlap length of wall panel is 100mm.
 自攻螺釘的選用。濟南彩鋼板房的 固定螺釘選用時應當依照結構的運用壽命選擇固定件,而且格外留意外覆資料的壽命與指定的固定件壽命是不是共同。一起留意鋼檁條厚度不能超越螺釘的自鉆才干。現在供給的螺絲可帶有塑料頭、不銹鋼頂蓋或涂有格外的耐久保護層。別的,除暗扣固定用螺釘外,其他螺釘均帶有防水墊圈,而且關于采光板的格外風壓下的狀況均配有相應的專用墊圈。
Selection of self tapping screws. Ji'nan color plate housing fixed screws should be selected in accordance with the structure of the life of the use of fixed parts, and pay special attention to the life of the material covered with the specified life is not a fixed joint. Together with attention to self drilling ability can not exceed the thickness of steel purlin screw. Now the screw can be provided with plastic head, stainless steel cover or coated with extra durable protective layer. Anything else, except the button is fixed by screws, other screws with waterproof gasket, and a lighting plate is caused by wind conditions are equipped with the corresponding special gasket.
濟南彩鋼板房的裝置較易把握,而一些細節的處理對比主要。關于濟南彩鋼板房屋面用彩鋼板應當在房頂及屋檐處將彩鋼板進行相應的收邊作業,其意圖是為了更有效地阻撓雨水進入屋面以內。
Ji'nan color steel board of the device is easy to grasp, and some of the details of the main treatment. On the Ji'nan color steel plate with the color plate should be in the roof and eaves of the color steel plate corresponding to the edge of the operation, its intention is to more effectively obstruct the rain into the roof.
屋面外板在屋脊的當地,都可用收邊東西將坐落鋼板終端肋條之間的地盤向上折。它用于一切斜度低于1/2(250)屋面鋼板的上端,以確保在泛水板或蓋板下方由風吹入的水下不會流入修建當中。邊收邊操作可在鋼板定位之前施行,也可在鋼板裝置以后施行,但后一種辦法要在鋼板的頂端留有滿足的空隙(約50mm),便于收邊作業的操作。其具體操作辦法是:把收邊東西坐落鋼板終端地盤之上,盡快將東西滑于鋼板之上,越里越好。用東西抓住鋼板終端,將地盤往上折,上折約800,如上所述,折彎每一地盤。當板被用在斜度低于1/5(100)的屋面時,應將鋼板下端的地盤端部略微向下曲折,可用同一收邊東西來完成,這么可確保雨水順著鋼板終端被掃除,而且不會因毛細或風力效果回流至平地盤的下邊。
The local board in the roof of the roof, all available edge things will be located between the steel plate rib site fold up terminal. It is used for all slope is lower than that of 1/2 (250) at the top of the roof plate, in order to ensure the water board orbelow cover by the wind blowing water will not flow into the construction. Edge closing operation can be carried out before the steel plate positioning, but also in the steel plate device after the implementation, but the latter approach to the top of the steel plate to be left to meet the gap (about 50mm), to facilitate the operation of the closing operations. The specific method of operation is: the edge of the thing is located on the steel plate terminal site, as soon as possible to slide on the steel plate, the better the better. Seize the steel plate with the tool, the site will be folded up, about 800 fold, as described above, bend each site. When the plate is used in the slope is lower than that of 1/5 (100) of the roof, the end of the site should be slightly lower plate bends downward, by the same edge things to do, so that rain down the steel terminal to be swept away and not due to capillary or wind effect back to the site under the flat side.
向下的折邊操作有必要在屋面鋼板被固定以后才干進行,否則這項操作將會遭到妨礙。下折板的邊端時,恰當張開下撬東西的口,將東西夾住地盤端,盡量向里堆。東西緊貼在地盤端部,一起將手柄搖擺約200,這么在鋼板的端部會構成一向下折邊。
It is necessary to have a downward flanging operation to be carried out after the roof plate is fixed, otherwise the operation will be affected. Under the flap edge, right under the open mouth will pry things, things between sites as far as possible to end in the heap. Close to the end of the site, the handle will swing about 200, so that the end of the plate will form a downward fold.
關于十分長的屋面鋼板,應設置彈性節點,距離不得大于下表中所列數據,以便客服縱向熱位移。這關于穿透固定式來說,在兩彈性節點之間,僅能設置一個穿透固定的搭接。
On the very long roof steel plate, should be set elastic node, the distance should not be greater than the data listed in the table below, so that customer service longitudinal thermal displacement. In this regard, through the fixed type, in the two elastic nodes, can only be set to a fixed through the overlap.
一般來說,在用于濟南彩鋼板房屋面和墻面板的一切金屬中,鋼的熱脹冷縮到現在停止是最低的。
In general, in all the metals used in the Ji'nan color steel plate housing and wall panels, the heat expansion and contraction of steel is the lowest.
事實上,在鋼板的終端和終究支持之間的脹大或縮短位移僅僅表中所顯示數據的一小有些,由于被固定的鋼板位移,通長是從基地開端趨向于鋼板的每個端部。每端的位移量僅僅脹大或縮短量的一半。同樣在修建結構或屋面結構中也有一些溫度改變位移,盡管不如屋面那么大,但仍減少了屋面板和其支持面之間的位移。終究,由于檁條的屈曲,格外是在跨中,更進一步減少了這種差動位移。
In fact, in the steel plate between the terminal and swell or shorten the displacement of support will only display the data in the table a little some, because the steel plate displacement is fixed, usually from each end of the base plate tends to start. The displacement of each end is only half or half of the amount. There are also some temperature changes in the construction of the structure or roof structure, although not as large as the roof, but still reduced the displacement between the roof and its support surface. After all, due to the purlin buckling, especially in the cross, to further reduce the differential displacement.
外形板都有相應的成型泡沫密封條。當它們被嵌在濟南彩鋼板房屋檐支持面和屋面板下邊之間時(用作屋檐密封),這一底部密封帶能夠避免灰塵、昆蟲、鳥、嚙齒動物以及雨水進入肋條空間內。
The shape plate has the corresponding forming foam sealing strip. When they are embedded in the Ji'nan color plate of eave roof panel between the support surface and bottom when (used as the roof seal), bottom sealing tape to avoid dust, insects, birds, rodents and rainwater into the rib space.
能夠沿泛水板和蓋板的下方,將一頂部有概括的成型條嵌入泛水板下方和屋面板頂面之間,并用雙面膠進行恰當的固定,從而起到類似的密封效果。這一點很主要,不進行這樣的處理,會形成房屋的漏水。
Can be below the water board and the cover plate, a top between the general molding strip is inserted into the water board and the roof panel below the top surface, and use double-sided adhesive properly fixed, so as to play a similar sealing effect. This is very important, do not carry out such a treatment, will form the housing leakage.

福利AV导航